 |
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
|
| If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
|
| Datasheet File OCR Text: |
| Communication ICs IrDA wireless communication transceiver IC (supports Ver.1.0) RPM851A Series The RPM851A series is an IC that supports IrDA Ver 1.0, and is ideal for wireless communications. An infrared LED, a pin-photo diode, and a receiver frequency formation LSI are all contained in a single package. Also equipped with low power consumption and power down functions making this IC perfect for mobile sets. FApplications Personal computers, PDAs, DVCs, digital cameras, printers, cellular phones, PHS systems, hand-held terminals, and others FFeatures 1) Supports IrDA Ver. 1.0 2) Low power consumption while standing by for reception (typ. 220A). 3) A power-down function is perfect for battery applications. 4) Supports a broad power supply voltage range from 2.7V to 5.5V. 5) The package supports mounting on both the upper and side surfaces. 6) Integrated shield case (RPM851A-H6) FAbsolute maximum ratings (Ta = 25_C) FRecommended operating conditions (Ta = 25_C) FSeries 651 Communication ICs FBlock diagram RPM851A Series 652 Communication ICs FPin descriptions RPM851A Series 653 Communication ICs RPM851A Series FElectrical characteristics (unless otherwise noted, LEDVCC = VCC = PINVCC = 3V, Ta = 25_C) FOptical characteristics (unless otherwise noted, LEDVCC = VCC = PDVCC = 3V, Ta = 25_C) 654 Communication ICs FCircuit operation Timing charts RPM851A Series FApplication example 655 Communication ICs FRecommended values (at VCC = 3V) RPM851A Series 656 Communication ICs FOperation notes (1) LEDVCC (pin5), VCC (pin122) and PINVCC (pin13) S Other power source can be used within 0.2 [V] voltage difference between LEDVCC and VCC. VCC and PINVCC should be supplied from the same source. (2) Caution in designing board lay-out S Pin1 is radiaton pin from LED as well. Wider pattern is better. S The line of RXDSIR (pin10) should be connected at backside via through hole close to RPM851A pin lead. Better not to be close to photo diode side (pin13). ! This is to minimize feedback supplied to photo diode from RXDSIR. S Capacitors for pin12 (VCC) and pin13 (PINVCC) should be placed close to RPM851A. FExternal dimensions (Units: mm) RPM851A Series S Better to be placed more than 1.0cm in radius from photo diode (pin13) and also away from the parts which generates noise, such as DC / DC converter. Digital signal line, such as clock pulse, bus etc, are also away more than 1.0cm in radius from photo diode. S As for C1, C2 and, GND should be close to pin7 and placed close to pins11, 12 and 13 (within 5mm). (3) Please be sure to set up the TXD (pin6) input to be "L" (under 0.5 [V]) except transmitting data (for < 90 s. ON Duty < 20%). (4) Powerdown current might increase if exposed by strong light (ex. direct sunlight) at powerdown mode. (5) Please use by the signal form which is specified by IrDA Ver1.0. There might be on error if used by different signal form. 657 |
Price & Availability of RPM851ASERIES
 |
|
|
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
| [Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
|
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |